Esters-buliding-blocks

In the next few decades, the world population will flourish. As the population grows rapidly and people all over the world use more and more resources, all industries must consider their environmental impact. 2318-25-4, name is Ethyl 3-ethoxy-3-iminopropionate hydrochloride belongs to esters-buliding-blocks compound, it is a common compound, a new synthetic route is introduced below. SDS of cas: 2318-25-4

Example P2: Preparation of Ethoxycarbonimidoyl-acetic acid ethyl ester. 25.7 g (0.131 mol) of ethoxycarbonimidoyl-acetic acid ethyl ester hydrochloride was suspended in 155 ml of dichlormethane and then a solution of 5.78 g (0.144 mol) of sodium hydroxide in 30 ml of water was added. After stirring for 30 min the layers were separated and the organics dried and vacced down to leave a colourless oil to give 19.35g of clean Ethoxycarbonimidoyl-acetic acid ethyl ester. 1H-NMR (CDCI3, ppm): 6.28 (s, br, 1 H), 4.19 (q, J=7 Hz, 2H), 4.02 (m, 2H), 3.37 (s, 1 H), 3.25 (s, 1 H), 1.30 (t, J=7Hz, 3H), 1.26 (t, J=7Hz, 3H).

The synthetic route of 2318-25-4 has been constantly updated, and we look forward to future research findings.

Reference:
Patent; SYNGENTA PARTICIPATIONS AG; SYNGENTA LIMITED; WO2008/6540; (2008); A1;,
Ester – Wikipedia,
Ester – an overview | ScienceDirect Topics

Adding a certain compound to certain chemical reactions, such as: 140-39-6, name is p-Tolyl Acetate, belongs to esters-buliding-blocks compound, can increase the reaction rate and produce products with better performance than those obtained under traditional synthetic methods. Here is a downstream synthesis route of the compound 140-39-6, HPLC of Formula: C9H10O2

General procedure: Catalyst (FSG) was purchased from Fluorous Technologies Inc. and used without further purification. Its synthesis procedure is reported by Curran et al. [24]. General procedure for Fries rearrangement was done by adding FSG to aryl ester at the ambient temperatures. Before adding FSG to reaction mixture, aryl esters were obtained by in situ formation through the reaction of acyl chloride derivatives and phenol derivatives. Thus, to a 100ml round bottom flask stirring by a magnetic bar 10mmol of phenols was added and then, 10mmol of acyl chloride derivatives (for catechols 20mmol) was added dropwise and allowed to react at room temperature. After 30min, temperature was raised to remove HCl from reaction mixture. Then 1g of FSG was added to reaction mixture at ambient temperature. After 4h heating at appropriate temperature in oil bath, the reaction mixture was cooled to room temperature and washed with dichloromethane. The catalyst was separated by filtration. The solvent was removed by rotary evaporator and resulting mixture was separated by column chromatography (stationary phase: silica-gel, eluent:hexane:ethyl acetate) and purified by recrystallization. All isolated products successfully gave related spectral data of IR, NMR, and mass spectrometers.

In the field of chemistry, the synthetic routes of compounds are constantly being developed and updated. I will also mention this compound in other articles, p-Tolyl Acetate, other downstream synthetic routes, hurry up and to see.

Reference:
Article; Ghaffarzadeh, Mohammad; Ahmadi, Maryam; Journal of Fluorine Chemistry; vol. 160; (2014); p. 77 – 81;,
Ester – Wikipedia,
Ester – an overview | ScienceDirect Topics

Application of 58656-98-7, In the next few decades, the world population will flourish. As the population grows rapidly and people all over the world use more and more resources, all industries must consider their environmental impact. 58656-98-7, name is tert-Butyl 4-fluorobenzoate belongs to esters-buliding-blocks compound, it is a common compound, a new synthetic route is introduced below.

Preparation of 4-[4-(2-Aminoethyl phenoxy]benzoic acid, tert-butyl ester Tyramine (700 mg, 5.1 mmol) was added to a magnetically stirred suspension of potassium hydride (35 wt. percent dispersion in oil; 876 mg, 7.64 mmol) in DMF (20 mL) at 25 C. After effervescence stopped, tert-butyl 4-fluorobenzoate (1.0 g, 5.1 mmol) was added. After stirring at 25 C. for 64 hours, the reaction was warmed to 60 C. After 48 h, the reaction was poured into brine and extracted with hexanes (3*25 mL) and ethyl acetate (2*25 mL). Organic layers washed separately with aqueous 2 N NaOH, dried (Na2SO4), then pooled, evaporated and purified by silica gel chromatography (CH2Cl2:MeOH/2:1) to provide 0.98 g of clear oil.

The synthetic route of tert-Butyl 4-fluorobenzoate has been constantly updated, and we look forward to future research findings.

Reference:
Patent; Brewster, William Kirkland; Demeter, David Anthony; Erickson, William Randal; Klittich, Carla Jean Rasmussen; Lowe, Christian Thomas; Rieder, Brent Jeffrey; Nugent, Jaime Susanne; Yerkes, Carla Nanette; Zhu, Yuanming; Balko, Terry William; US2007/93498; (2007); A1;,
Ester – Wikipedia,
Ester – an overview | ScienceDirect Topics

Electric Literature of 57486-68-7,Some common heterocyclic compound, 57486-68-7, name is Methyl 2-chlorophenylacetate, molecular formula is C9H9ClO2, traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc, below Introduce a new synthetic route.

Reference Example Al4; (1) To a solution of methyl 2-chlorophenylacetate (10 g) in dimethylformamide (150 mL) was added N, N- dimethylformamide dimethylacetal (14.4 mL) , and the mixture was stirred at 85C overnight. After cooling to room temperature, to the reaction mixture was added ethyl acetate and water. After stirring, the organic layer was separated, dried over sodium sulfate and filtered, and the filtrate was concentrated in vacuo. The residue was diluted with acetic acid (18 mL) , and -thereto were added 3- amino-4-ethoxycarbonyl-lH-pyrazole (8.4 g) and piperidine(1.1 mL) . The mixture was stirred at 800C for 3.5 hours.After cooling to room temperature, to the reaction mixture were added ethyl acetate and water. The mixture was stirred and filtered, and the resultant -? precipitates were dried to give 3- [2- (2-chlorophenyl) -2-methoxycarbonyl- vinylamino] -4-ethoxycarbonyl-lH-pyrazole (11.8 g, yield: 62%) as a powder. MS(APCI)m/z; 350/352 [M+H]+; Reference Example A14B; To a solution of methyl 2-chlorophenylacetate (25 g) in dimethylformamide (400 itiL) was added N, N- dimethylformamide diralphaethylacetal (36 itiL) , and the mixture was stirred at 90 C overnight. After cooling to room temperature, to the reaction mixture were added ethyl acetate and water. After stirring, the organic layer was separated, dried over magnesium sulfate and filtered, and the filtrate was concentrated in vacuo. The residue was diluted with acetic acid (60 itiL) , and thereto was added 3- amino~4-ethoxycarbonyl-5-methyl-lH-pyrazole (19.7 g) . The mixture was stirred at 1200C overnight. After cooling the reaction mixture to room temperature, the precipitates were collected by filtration, washed with ethyl acetate/diisopropylether (1/1) and dried to give 6- (2- chlorophenyl) -3-ethoxycarbonyl-2-methyl-7-oxo-4 , 7- dihydropyrazolo [1, 5-a] pyrimidine (26.0 g) as a powder. MS(APCI)m/z; 332/334 [M+H]+

The synthetic route of 57486-68-7 has been constantly updated, and we look forward to future research findings.

Reference:
Patent; MITSUBISHI TANABE PHARMA CORPORATION; WO2008/4698; (2008); A2;,
Ester – Wikipedia,
Ester – an overview | ScienceDirect Topics

Reference of 685-88-1,Some common heterocyclic compound, 685-88-1, name is Diethyl fluoromalonate, molecular formula is C7H11FO4, traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc, below Introduce a new synthetic route.

Step 1: Synthesis of 2-( 1 -(2,3 -difluorobenzyl)-5 -(difluoromethoxy)- 1 H-pyrazol-3 -yl)-5- fluoropyrimidine-4,6-diol To a mixture containing diethyl 2-fluoromalonate (2 equiv.) and1 -(2,3 -difluorobenzyl)-5 -(difluoromethoxy)- 1 H-pyrazole-3 -carboximidamide hydrochloride (Described in step 3 towards the synthesis of Compound 1-52 (1 equiv.) in methanol was added a 25 wt% solution of sodium methoxide in methanol (5 equiv.). The mixture was stirred at 23 C for 1 h. To this mixture, was added HC1 (5 equiv.). The mixture was stirred vigorously for 15 mm. The precipitate formed was collected by filtration and dried under vacuum to deliver the desired intermediate, 2-( 1 -(2,3 -difluorobenzyl)-5-(difluoromethoxy)- 1 H-pyrazol-3 -yl)-5 -fluoropyrimidine-4,6-diol (475 mg, 44 % yield) as a cream colored solid.?H NMR (500 MHz, DMSO-d6) ppm 7.19 – 7.57 (m, 3 H), 7.11 – 7.16 (m, 1 H), 6.71 (s, 1 H), 5.41 (s, 2H).

These compound has a wide range of applications. It is believed that with the continuous development of the source of the synthetic route Diethyl fluoromalonate, its application will become more common.

Reference:
Patent; IRONWOOD PHARMACEUTICALS, INC.; RENHOWE, Paul Allen; SHEPPECK, James Edward; NAKAI, Takashi; IYER, Karthik; PERL, Nicholas Robert; RENNIE, Glen Robert; WO2015/89182; (2015); A1;,
Ester – Wikipedia,
Ester – an overview | ScienceDirect Topics

Researchers who often do experiments know that organic synthesis is a process of preparing more complex target molecules from simple raw materials through one or more chemical reactions. Generally, it requires fewer steps, and cheap raw materials. 924-99-2, name is Ethyl 3-(dimethylamino)acrylate, A new synthetic method of this compound is introduced below., Application In Synthesis of Ethyl 3-(dimethylamino)acrylate

General procedure: All microwave reactions were carried out in a capped (10 mL) microwave-vessel (Borosilicate glass vial sealed) that was placed in a microwave cavity. The pressure was set at 17 bar (average of an effective pressure = 4 bar) with power 75 W. DIEA (3.4 g, 3.4 mmol) was added to a solution of either 2,5-difluoro-4-(pyrrolidin-1-yl) benzoylchloride 12 (0.83 g, 3.4 mmol) or 2,5-difluoro-4-(pyrrolidin-1-yl)benzothioyl chloride 13 (0.88 g, 3.4 mmol) and ethyl-3-(diethylamino)acrylate 14 (0.45 g, 3.1 mmol) in acetonitrile (5 mL). The mixture reaction was held at 100 C for 20 min. After the reaction vessel was cooled to room temperature, the crude product was diluted with water (10 mL) and extracted with ethyl acetate(3 ¡Á 10 mL). The organic layers were combined, dried over Na2SO4, filtered, evaporated and purified by a flash column chromatography (eluent n-hexane: acetone, 3:1)to give the titled compounds. Ethyl-2-(2,5-difluoro-4-(pyrrolidin-1-yl)benzoyl)-3-(dimethylamino) acrylate (15)Yellow oil (Rf = 0.3), Yield 85%. IR (KBr) numax in cm-1:2993 (C-H, Ar), 2953 (C-H), 1760 (C=O), 1692 (C=O),1654 (C=C, Ar), 1592 (C-N). 1H NMR (400 MHz, DMSOd6):delta = 7.77 (1H, s, CH), 7.32 (1H, d, J = 5.0 Hz, CH-Ar),6.88 (1H, d, J = 5.2 Hz, CH-Ar), 4.2 (2H, q, J = 7.1 Hz,CH2), 3.47-3.42 (4H, m, 2CH2), 3.1 (6H, s, 2CH3), 2.01-1.97 (4H, m, 2CH2), 1.32 (3H, t, J = 4.2 Hz, CH3).

The synthetic route of 924-99-2 has been constantly updated, and we look forward to future research findings.

Reference:
Article; Almashal, Faeza A.; Alshawi, Jasim M.; Dhumad, Adil M.; Jassem, Ahmed M.; Medicinal Chemistry Research; (2020);,
Ester – Wikipedia,
Ester – an overview | ScienceDirect Topics

Researchers who often do experiments know that organic synthesis is a process of preparing more complex target molecules from simple raw materials through one or more chemical reactions. Generally, it requires fewer steps, and cheap raw materials. 685-88-1, name is Diethyl fluoromalonate, A new synthetic method of this compound is introduced below., SDS of cas: 685-88-1

General procedure: All flasks and stirrer bars were flame dried before use. Tothe N-oxide (0.2 mmol, 1.0 equiv.), dissolved in 2 cm3dichloromethane was added Tf2O (0.3 mmol, 1.5 equiv.) at0 C. In another flask, a suspension of NaH (0.7 mmol, 3.5equiv.) in 1 cm3 tetrahydrofuran was cooled to 0 C andthe malonate (0.7 mmol, 3.5 equiv.) was added. After15 min, the malonate solution was added to the activatedN-oxide solution and the mixture was stirred at roomtemperature for 1 h. The reaction was quenched withNH4Cl solution and the aqueous phase was extracted withdichloromethane. The combined organic layers werewashed with brine before being dried over MgSO4. Thesolvents were removed under reduced pressure and thecrude product was purified by column chromatography.

The synthetic route of 685-88-1 has been constantly updated, and we look forward to future research findings.

Reference:
Erratum; Lemmerer, Miran; Teskey, Christopher J.; Kaiser, Daniel; Maulide, Nuno; Monatshefte fur Chemie; vol. 149; 4; (2018); p. 721 – 722;,
Ester – Wikipedia,
Ester – an overview | ScienceDirect Topics

Related Products of 5941-55-9, These common heterocyclic compound, 5941-55-9, name is Ethyl (E)-3-Ethoxyacrylate, its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc, below Introduce a new synthetic route.

A mixture of ethyl-5-amino-1H-pyrazole-4-carboxylate (20.0 g, 129 mmol), (E)-ethyl 3-ethoxyacrylate (22.4 mL, 155 mmol) and cesium carbonate (63.0 g, 193 mmol) in DMF (322 mL) was stirred at 110 C. overnight. After being cooled to 0 C., the reaction mixture was acidified with 2 N aq. HCl. A precipitated solid was collected by filtration and washed with water and EtOAc to afford ethyl 5-oxo-4,5-dihydropyrazolo[1,5-a]pyrimidine-3-carboxylate (24.7 g, 92%) as a pale yellow solid. 1H-NMR (DMSO-d6, Varian, 400 MHz): delta 1.27 (3H, t, J=7.2 Hz), 4.80 (2H, q, J=6.8 Hz), 6.16 (1H, d, J=8.0 Hz), 8.14 (1H, s), 8.58 (1H, d, J=8.0 Hz), 11.7 (1H, br. s).

The synthetic route of 5941-55-9 has been constantly updated, and we look forward to future research findings.

Reference:
Patent; HANDOK INC.; CMG Pharmaceutical Co., Ltd.; Kim, Moonsoo; Lee, Chaewoon; Lee, Gilnam; Yoon, Cheolhwan; Seo, Jeongbeob; Kim, Jay Hak; Lee, Minwoo; Jeong, Hankyul; Choi, Hyang; Jung, Myung Eun; Lee, Ki Nam; Kim, Hyun Jung; Kim, Hye Kyoung; Lee, Jae Il; Lee, MinWoo; Kim, Misoon; Choi, Soongyu; (124 pag.)US2016/168156; (2016); A1;,
Ester – Wikipedia,
Ester – an overview | ScienceDirect Topics

Application of 64123-77-9,Some common heterocyclic compound, 64123-77-9, name is Methyl 2-(3-fluorophenyl)acetate, molecular formula is C9H9FO2, traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc, below Introduce a new synthetic route.

(ab) from methyl m-fluorophenylacetate and methyl formate there was obtained methyl 2-(m-fluorophenyl)-3-hydroxy-acrylate of b.p. 75-81/0.1 mm;

These compound has a wide range of applications. It is believed that with the continuous development of the source of the synthetic route Methyl 2-(3-fluorophenyl)acetate, its application will become more common.

Reference:
Patent; Hoffmann-La Roche Inc.; US4735940; (1988); A;,
Ester – Wikipedia,
Ester – an overview | ScienceDirect Topics

Researchers who often do experiments know that organic synthesis is a process of preparing more complex target molecules from simple raw materials through one or more chemical reactions. Generally, it requires fewer steps, and cheap raw materials. 89-71-4, name is Methyl 2-methylbenzoate, A new synthetic method of this compound is introduced below., Recommanded Product: 89-71-4

General procedure: To a solution of 6.0 g (0.04 mol) of methyl 2-methylbenzoate derivatives in 38 mL of chloroform, 7.5 g (0.042 mol) of N-bromosuccinimide and 0.078 g of benzoyl peroxide were added and carefully warmed up to 65 C until reaction started. Then the mixture was refluxed for 5 h. After cooling down to room temperature, the deposit of succinimide was filtered. The solvent was removed under reduced pressure and the crude product was used in the next step without further purification. To a solution of functionalized methyl 2-(bromomethyl)benzoate (6.55 mmol), substituted phenol (8.5 mmol), K3PO4 (16.4 mmol) and toluene 20 mL were added to Schlenk under argon. The resulting solution was stirred to 110 C for 5 h. The progress of the reaction was monitored by TLC. The mixture was extracted with EtOAc, washed with water, brine and the combined organic layers were dried over anhydrous Na2SO4and the solvent was removed under reduced pressure. The crude product was used in the next step without further purification. To the solution of the ester (0.015 mol) in MeOH (73 mL), was added 13 mL aqueous KOH (20%) and refluxed at 80C for 5 h. MeOH was removed and the aqueous phase was washed with DCM. After acidifying with HCl (10%) the deposit was collected and washed with water.

The synthetic route of 89-71-4 has been constantly updated, and we look forward to future research findings.

Reference:
Article; Scoccia, Jimena; Castro, M. Julia; Faraoni, M. Belen; Bouzat, Cecilia; Martin, Victor S.; Gerbino, Dario C.; Tetrahedron; vol. 73; 20; (2017); p. 2913 – 2922;,
Ester – Wikipedia,
Ester – an overview | ScienceDirect Topics